Update 3D model
This commit is contained in:
+378
-238
@@ -1,290 +1,430 @@
|
|||||||
# IMU Pointer Enclosure
|
"""
|
||||||
|
IMU Pointer Enclosure — v6
|
||||||
|
============================
|
||||||
|
Fixes from v5 (diagnosed from rendered images):
|
||||||
|
|
||||||
|
1. BOTTOM HOLE:
|
||||||
|
v5 built the bottom shell from a full-height box (0→H) then trimmed
|
||||||
|
at SPLIT_Z. The taper wedge interacted badly with the split cut near
|
||||||
|
X=0 leaving a hole in the floor. Fix: build bottom outer solid only
|
||||||
|
to SPLIT_Z height — no trimming step needed, no interaction.
|
||||||
|
|
||||||
|
2. TOP SHELL WALLS PROTRUDING BELOW SPLIT:
|
||||||
|
v5 top_outer started at SPLIT_Z but the cavity inside started at
|
||||||
|
SPLIT_Z + WALL, leaving WALL=3.5mm of solid wall below the groove —
|
||||||
|
visually protruding past the bottom shell. Fix: the top shell outer
|
||||||
|
solid starts at SPLIT_Z. The groove is cut starting exactly at SPLIT_Z
|
||||||
|
so there is zero protrusion below the split line.
|
||||||
|
|
||||||
|
3. BUTTON CAP NOT FLUSH / SITTING PROUD:
|
||||||
|
Aperture cylinder had arithmetic-derived Z that could miss the top wall
|
||||||
|
faces after filleting. Fix: aperture runs from Z=SPLIT_Z (well inside
|
||||||
|
the cavity) all the way to Z=H+2 — brute-force punch, impossible to miss.
|
||||||
|
|
||||||
|
4. CAP RIM SITS UNDER OUTER FACE (not above it):
|
||||||
|
Cap is placed so shaft top = H (flush). Rim hangs BELOW the top face
|
||||||
|
inside the cavity — correct retention geometry. The cap shaft top is
|
||||||
|
exactly flush with H. No part of the cap protrudes above H.
|
||||||
|
|
||||||
|
Split joint design:
|
||||||
|
- Bottom shell has a TONGUE that projects UP from SPLIT_Z.
|
||||||
|
The tongue is a thin rectangular frame (inner perimeter of the walls).
|
||||||
|
- Top shell has a matching GROOVE cut into the inside of its lower edge,
|
||||||
|
starting exactly at SPLIT_Z (the bottom face of the top shell).
|
||||||
|
- Two flex notches cut through the tongue on the long sides allow snap fit.
|
||||||
|
"""
|
||||||
|
|
||||||
import FreeCAD as App
|
import FreeCAD as App
|
||||||
import FreeCADGui as Gui
|
import FreeCADGui as Gui
|
||||||
import Part
|
import Part
|
||||||
|
import math
|
||||||
from FreeCAD import Base
|
from FreeCAD import Base
|
||||||
|
|
||||||
doc = App.newDocument("pointer")
|
doc = App.newDocument("pointer_v7")
|
||||||
|
|
||||||
# Global dimensions
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
L = 115.0
|
# DIMENSIONS
|
||||||
W = 36.0
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
H = 20.0
|
L = 115.0 # length (X): front=0, back=L
|
||||||
WALL = 3.5
|
W = 36.0 # width (Y)
|
||||||
CR = 3.0
|
H = 22.0 # height (Z): bottom=0, top=H
|
||||||
TOL = 0.25
|
WALL = 4.5 # wall thickness (+1 mm vs v6 — closes taper floor gap)
|
||||||
|
CR = 5.0 # corner fillet radius (vertical edges)
|
||||||
|
TOL = 0.25 # fit tolerance
|
||||||
|
|
||||||
# Rail and lid
|
# Taper: front of bottom shell is TAPER_RISE mm shorter than back.
|
||||||
RAIL_H = 4.5
|
# Applied only to the BOTTOM shell (it's where the ergonomic taper lives).
|
||||||
RAIL_D = 2.0
|
TAPER_RISE = 0.0 # no taper — removed per user request
|
||||||
LIP_H = 2.0
|
TAPER_LEN = 100.0 # unused but kept to avoid NameError
|
||||||
LIP_OVER = 1.5
|
|
||||||
LIP_EMBED = 0.2
|
|
||||||
|
|
||||||
LID_H = RAIL_H - LIP_H - TOL - 0.55
|
# Split plane
|
||||||
|
USBC_W = 11.0
|
||||||
|
USBC_H = 7.0
|
||||||
|
USBC_Z = 5.0
|
||||||
|
SPLIT_Z = USBC_Z + USBC_H + 2.5 # = 14.5 mm
|
||||||
|
|
||||||
# Board dimensions
|
# Tongue/groove clip joint
|
||||||
PCB_T = 1.0
|
TONGUE_H = 2.5 # how far tongue projects above SPLIT_Z
|
||||||
BRD_L = 21.0
|
TONGUE_T = 1.2 # tongue wall thickness
|
||||||
BRD_W = 17.5
|
GROOVE_H = TONGUE_H + TOL
|
||||||
BRD_X = WALL
|
GROOVE_T = TONGUE_T + TOL
|
||||||
BRD_Y = (W - BRD_W) / 2
|
|
||||||
|
|
||||||
|
# Flex notch through tongue (for snap release)
|
||||||
|
NOTCH_W = 8.0
|
||||||
|
NOTCH_H = TONGUE_H + 0.5
|
||||||
|
|
||||||
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
|
# IMU BOARD
|
||||||
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
|
PCB_T = 1.0
|
||||||
|
BRD_L = 21.0
|
||||||
|
BRD_W = 17.5
|
||||||
|
BRD_X = WALL
|
||||||
|
BRD_Y = (W - BRD_W) / 2.0
|
||||||
PLATFORM_H = 0.5
|
PLATFORM_H = 0.5
|
||||||
BRD_Z = WALL + PLATFORM_H
|
BRD_Z = WALL + PLATFORM_H
|
||||||
|
ARM_LEN = 5.0
|
||||||
|
ARM_THICK = 1.6
|
||||||
|
ARM_H = BRD_Z + PCB_T + 0.8
|
||||||
|
CLIP_TOL = 0.35
|
||||||
|
|
||||||
# Clip arms
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
ARM_LEN = 5.0
|
# BATTERY BAY
|
||||||
ARM_THICK = 1.6
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
ARM_H = BRD_Z + PCB_T + 0.8
|
BAT_L = 50.0
|
||||||
CLIP_TOL = 0.35
|
BAT_W = 12.0
|
||||||
|
BAT_H = 12.0
|
||||||
|
BAT_X = BRD_X + BRD_L + 8.0
|
||||||
|
BAT_Y = (W - BAT_W) / 2.0
|
||||||
|
BAT_CLIP_Y = 8.0
|
||||||
|
|
||||||
# USB-C cutout
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
USBC_W = 11.0
|
# BUTTON
|
||||||
USBC_H = 7.0
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
USBC_Z = 4.5
|
BTN_X = 28.0
|
||||||
|
BTN_CY = W / 2.0
|
||||||
|
BTN_HOLE_R = 8.0
|
||||||
|
CAP_SHAFT_R = BTN_HOLE_R - 0.4 # 0.4 mm radial clearance in hole
|
||||||
|
CAP_SHAFT_H = WALL # shaft fills top wall → top face flush
|
||||||
|
CAP_RIM_R = BTN_HOLE_R + 2.0 # 2 mm wider than hole → retention
|
||||||
|
CAP_RIM_H = 1.5
|
||||||
|
NUBBIN_R = 1.8
|
||||||
|
NUBBIN_H = 2.0
|
||||||
|
|
||||||
# Battery section
|
# Switch geometry (adjust to match your Omron)
|
||||||
BAT_L = 50.0
|
SWITCH_BODY_H = 5.0
|
||||||
BAT_W = 12.0
|
STEM_H = 2.5
|
||||||
BAT_H = 12.0
|
GAP = 0.5
|
||||||
BAT_X = BRD_X + BRD_L + 8.0
|
|
||||||
BAT_Y = (W - BAT_W) / 2
|
|
||||||
BAT_CLIP_Y = 8.0
|
|
||||||
|
|
||||||
# Circular notch
|
# PCB position derived top-down
|
||||||
NOTCH_R = (USBC_W + TOL) / 2
|
PCB_TOP_Z = H - WALL - CAP_RIM_H - NUBBIN_H - GAP - SWITCH_BODY_H - STEM_H
|
||||||
NOTCH_DEPTH = WALL + 2.0
|
PCB_BOT_Z = PCB_TOP_Z - PCB_T
|
||||||
|
# Clamp: must be inside the top shell cavity
|
||||||
|
floor_top_shell = SPLIT_Z + WALL
|
||||||
|
if PCB_BOT_Z < floor_top_shell + 0.5:
|
||||||
|
PCB_BOT_Z = floor_top_shell + 0.5
|
||||||
|
PCB_TOP_Z = PCB_BOT_Z + PCB_T
|
||||||
|
|
||||||
|
POST_H = PCB_BOT_Z - floor_top_shell
|
||||||
|
POST_OD = 4.0; POST_R = POST_OD / 2.0
|
||||||
|
POST_ID = 1.9; POST_IR = POST_ID / 2.0
|
||||||
|
POST_SEP = 3.0
|
||||||
|
|
||||||
# Circular notch helper
|
BPCB_L = 16.0
|
||||||
def circular_notch(face_x, cy, cz, r, depth):
|
BPCB_W = 16.0
|
||||||
circle = Part.makeCircle(r, Base.Vector(face_x, cy, cz), Base.Vector(1, 0, 0))
|
SHELF_WALL = 2.0
|
||||||
face = Part.Face(Part.Wire(circle))
|
|
||||||
return face.extrude(Base.Vector(-depth, 0, 0))
|
|
||||||
|
|
||||||
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
|
# HELPERS
|
||||||
|
# ─────────────────────────────────────────────────────────────────────────────
|
||||||
|
|
||||||
# Rounded box helper
|
def box(lx, ly, lz, ox=0.0, oy=0.0, oz=0.0):
|
||||||
def rbox(lx, ly, lz, ox=0, oy=0, oz=0, r=CR):
|
|
||||||
b = Part.makeBox(lx, ly, lz, Base.Vector(ox, oy, oz))
|
|
||||||
try:
|
|
||||||
vert = [e for e in b.Edges
|
|
||||||
if abs(e.Vertexes[0].Z - e.Vertexes[1].Z) > lz * 0.9]
|
|
||||||
if vert:
|
|
||||||
b = b.makeFillet(r, vert)
|
|
||||||
except Exception:
|
|
||||||
pass
|
|
||||||
return b
|
|
||||||
|
|
||||||
|
|
||||||
# Simple box helper
|
|
||||||
def box(lx, ly, lz, ox=0, oy=0, oz=0):
|
|
||||||
return Part.makeBox(lx, ly, lz, Base.Vector(ox, oy, oz))
|
return Part.makeBox(lx, ly, lz, Base.Vector(ox, oy, oz))
|
||||||
|
|
||||||
|
def cyl(r, h, cx=0.0, cy=0.0, cz=0.0):
|
||||||
|
return Part.makeCylinder(r, h, Base.Vector(cx, cy, cz))
|
||||||
|
|
||||||
# Rounded slot helper
|
def rounded_slot(depth, sw, sh, ox, oy, oz):
|
||||||
def rounded_slot(depth, w, h, ox, oy, oz, r=None):
|
"""Stadium slot extruded in +X."""
|
||||||
if r is None:
|
r = min(sh / 2.0, sw / 2.0)
|
||||||
r = h / 2.0
|
cy = oy + sw / 2.0
|
||||||
|
cz = oz + sh / 2.0
|
||||||
|
hw = max(sw / 2.0 - r, 0.0)
|
||||||
|
if hw < 1e-6:
|
||||||
|
circ = Part.makeCircle(r, Base.Vector(ox, cy, cz), Base.Vector(1, 0, 0))
|
||||||
|
return Part.Face(Part.Wire(circ)).extrude(Base.Vector(depth, 0, 0))
|
||||||
|
l_s = Base.Vector(ox, cy - hw, cz - r)
|
||||||
|
l_m = Base.Vector(ox, cy - hw - r, cz)
|
||||||
|
l_e = Base.Vector(ox, cy - hw, cz + r)
|
||||||
|
r_s = Base.Vector(ox, cy + hw, cz + r)
|
||||||
|
r_m = Base.Vector(ox, cy + hw + r, cz)
|
||||||
|
r_e = Base.Vector(ox, cy + hw, cz - r)
|
||||||
|
wire = Part.Wire([Part.Arc(l_s, l_m, l_e).toShape(),
|
||||||
|
Part.makeLine(l_e, r_s),
|
||||||
|
Part.Arc(r_s, r_m, r_e).toShape(),
|
||||||
|
Part.makeLine(r_e, l_s)])
|
||||||
|
return Part.Face(wire).extrude(Base.Vector(depth, 0, 0))
|
||||||
|
|
||||||
r = min(r, h / 2.0, w / 2.0)
|
def fillet_vert(solid, r, min_len=4.0):
|
||||||
|
"""Fillet edges that are primarily vertical (parallel to Z)."""
|
||||||
import math
|
try:
|
||||||
|
edges = [e for e in solid.Edges
|
||||||
cy = oy + w / 2.0
|
if len(e.Vertexes) == 2
|
||||||
cz = oz + h / 2.0
|
and abs(e.Vertexes[0].X - e.Vertexes[1].X) < 1e-3
|
||||||
hw = w / 2.0 - r
|
and abs(e.Vertexes[0].Y - e.Vertexes[1].Y) < 1e-3
|
||||||
|
and e.Length >= min_len]
|
||||||
def pt(cx, cy_v, cz_v, angle_deg, radius):
|
if edges:
|
||||||
a = math.radians(angle_deg)
|
return solid.makeFillet(r, edges)
|
||||||
return Base.Vector(
|
except Exception as e:
|
||||||
cx,
|
print(f" fillet_vert skipped: {e}")
|
||||||
cy_v + radius * math.cos(a),
|
return solid
|
||||||
cz_v + radius * math.sin(a)
|
|
||||||
)
|
|
||||||
|
|
||||||
l_start = pt(ox, cy - hw, cz, 270, r)
|
|
||||||
l_mid = pt(ox, cy - hw, cz, 180, r)
|
|
||||||
l_end = pt(ox, cy - hw, cz, 90, r)
|
|
||||||
arc_left = Part.Arc(l_start, l_mid, l_end).toShape()
|
|
||||||
|
|
||||||
line_top = Part.makeLine(
|
|
||||||
l_end,
|
|
||||||
pt(ox, cy + hw, cz, 90, r)
|
|
||||||
)
|
|
||||||
|
|
||||||
r_start = pt(ox, cy + hw, cz, 90, r)
|
|
||||||
r_mid = pt(ox, cy + hw, cz, 0, r)
|
|
||||||
r_end = pt(ox, cy + hw, cz, 270, r)
|
|
||||||
arc_right = Part.Arc(r_start, r_mid, r_end).toShape()
|
|
||||||
|
|
||||||
line_bot = Part.makeLine(r_end, l_start)
|
|
||||||
|
|
||||||
wire = Part.Wire([arc_left, line_top, arc_right, line_bot])
|
|
||||||
face = Part.Face(wire)
|
|
||||||
|
|
||||||
return face.extrude(Base.Vector(depth, 0, 0))
|
|
||||||
|
|
||||||
|
|
||||||
# Board clip helper
|
|
||||||
def make_clip(corner_x, corner_y, inward_x, inward_y):
|
|
||||||
|
|
||||||
|
def make_clip(cx, cy, ix, iy):
|
||||||
plat_w = ARM_THICK + CLIP_TOL
|
plat_w = ARM_THICK + CLIP_TOL
|
||||||
|
plat_x = cx if ix > 0 else cx - plat_w
|
||||||
|
plat_y = cy if iy > 0 else cy - plat_w
|
||||||
|
plat = box(plat_w, plat_w, PLATFORM_H + PCB_T, plat_x, plat_y, WALL)
|
||||||
|
ax_ox = cx if ix > 0 else cx - ARM_LEN
|
||||||
|
ax_oy = cy - ARM_THICK - CLIP_TOL if iy > 0 else cy + CLIP_TOL
|
||||||
|
arm_x = box(ARM_LEN, ARM_THICK, ARM_H, ax_ox, ax_oy, WALL)
|
||||||
|
ay_oy = cy if iy > 0 else cy - ARM_LEN
|
||||||
|
ay_ox = cx - ARM_THICK - CLIP_TOL if ix > 0 else cx + CLIP_TOL
|
||||||
|
arm_y = box(ARM_THICK, ARM_LEN, ARM_H, ay_ox, ay_oy, WALL)
|
||||||
|
cb_w = ARM_THICK + CLIP_TOL
|
||||||
|
cb_ox = cx - cb_w if ix > 0 else cx
|
||||||
|
cb_oy = cy - cb_w if iy > 0 else cy
|
||||||
|
cb = box(cb_w, cb_w, ARM_H, cb_ox, cb_oy, WALL)
|
||||||
|
return plat.fuse(arm_x.fuse(arm_y).fuse(cb))
|
||||||
|
|
||||||
plat_x = corner_x if inward_x > 0 else corner_x - plat_w
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
plat_y = corner_y if inward_y > 0 else corner_y - plat_w
|
# BOTTOM SHELL (Z = 0 → SPLIT_Z, open on top)
|
||||||
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
|
|
||||||
platform = box(
|
# 1. Outer solid — built ONLY to SPLIT_Z height
|
||||||
plat_w, plat_w,
|
bot_outer = box(L, W, SPLIT_Z)
|
||||||
PLATFORM_H + PCB_T,
|
bot_outer = fillet_vert(bot_outer, CR, min_len=SPLIT_Z * 0.4)
|
||||||
plat_x, plat_y, WALL
|
|
||||||
)
|
|
||||||
|
|
||||||
ax_ox = corner_x if inward_x > 0 else corner_x - ARM_LEN
|
# Fillet the long horizontal edges the user holds.
|
||||||
ax_oy = corner_y - ARM_THICK - CLIP_TOL if inward_y > 0 else corner_y + CLIP_TOL
|
# These are the 4 edges running in X at Z≈0 and Z≈SPLIT_Z, on both long sides.
|
||||||
arm_x = box(ARM_LEN, ARM_THICK, ARM_H, ax_ox, ax_oy, WALL)
|
# Same fillet applied to equivalent edges on the top shell later.
|
||||||
|
EDGE_FILLET = 2.5 # mm — soft and comfortable, visible but not decorative
|
||||||
|
try:
|
||||||
|
h_edges = []
|
||||||
|
for e in bot_outer.Edges:
|
||||||
|
if len(e.Vertexes) != 2:
|
||||||
|
continue
|
||||||
|
v0, v1 = e.Vertexes[0], e.Vertexes[1]
|
||||||
|
dx = abs(v0.X - v1.X)
|
||||||
|
dz = abs(v0.Z - v1.Z)
|
||||||
|
dy = abs(v0.Y - v1.Y)
|
||||||
|
# Long edge in X, horizontal, on a long side face —
|
||||||
|
# but ONLY at Z≈0 (bottom face). Exclude Z≈SPLIT_Z (the join edge).
|
||||||
|
z_mid = (v0.Z + v1.Z) / 2.0
|
||||||
|
if dx > L * 0.5 and dz < 0.5 and dy < 0.5 and z_mid < 1.0:
|
||||||
|
h_edges.append(e)
|
||||||
|
if h_edges:
|
||||||
|
bot_outer = bot_outer.makeFillet(EDGE_FILLET, h_edges)
|
||||||
|
print(f"Bottom shell: filleted {len(h_edges)} horizontal edge(s) R={EDGE_FILLET}")
|
||||||
|
else:
|
||||||
|
print("Bottom shell: no horizontal edges found — skipped")
|
||||||
|
except Exception as exc:
|
||||||
|
print(f"Bottom shell horizontal fillet skipped: {exc}")
|
||||||
|
|
||||||
ay_oy = corner_y if inward_y > 0 else corner_y - ARM_LEN
|
# No taper wedge — removed per user request
|
||||||
ay_ox = corner_x - ARM_THICK - CLIP_TOL if inward_x > 0 else corner_x + CLIP_TOL
|
|
||||||
arm_y = box(ARM_THICK, ARM_LEN, ARM_H, ay_ox, ay_oy, WALL)
|
|
||||||
|
|
||||||
corner_block_w = ARM_THICK + CLIP_TOL
|
# 3. Inner cavity — floor at WALL, ceiling at SPLIT_Z (open top, no ceiling)
|
||||||
cb_ox = corner_x - corner_block_w if inward_x > 0 else corner_x
|
bot_cav_lx = L - WALL * 2
|
||||||
cb_oy = corner_y - corner_block_w if inward_y > 0 else corner_y
|
bot_cav_ly = W - WALL * 2
|
||||||
|
bot_cav_lz = SPLIT_Z - WALL # floor(WALL) → SPLIT_Z
|
||||||
|
bot_inner = box(bot_cav_lx, bot_cav_ly, bot_cav_lz, WALL, WALL, WALL)
|
||||||
|
bot_shell = bot_outer.cut(bot_inner)
|
||||||
|
|
||||||
corner_block = box(
|
# 4. Tongue (projects UP from SPLIT_Z, inner perimeter frame)
|
||||||
corner_block_w, corner_block_w, ARM_H,
|
# Outer edge of tongue = inner face of outer wall = WALL from outside
|
||||||
cb_ox, cb_oy, WALL
|
# Inner edge of tongue = WALL + TONGUE_T from outside
|
||||||
)
|
t_slab = box(bot_cav_lx, bot_cav_ly, TONGUE_H,
|
||||||
|
WALL, WALL, SPLIT_Z)
|
||||||
|
t_cut = box(bot_cav_lx - TONGUE_T*2, bot_cav_ly - TONGUE_T*2, TONGUE_H + 1,
|
||||||
|
WALL + TONGUE_T, WALL + TONGUE_T, SPLIT_Z - 0.5)
|
||||||
|
tongue = t_slab.cut(t_cut)
|
||||||
|
|
||||||
return platform.fuse(arm_x.fuse(arm_y).fuse(corner_block))
|
# Flex notches on the two long sides (parallel to X)
|
||||||
|
nx0 = L / 2.0 - NOTCH_W / 2.0
|
||||||
|
for ny_start in [WALL, W - WALL - TONGUE_T]:
|
||||||
|
tongue = tongue.cut(
|
||||||
|
box(NOTCH_W, TONGUE_T + 0.5, NOTCH_H,
|
||||||
|
nx0, ny_start - 0.1, SPLIT_Z - 0.1))
|
||||||
|
bot_shell = bot_shell.fuse(tongue)
|
||||||
|
|
||||||
|
# 5. IMU clips
|
||||||
# Base outer body
|
for cx, cy, ix, iy in [
|
||||||
base = rbox(L, W, H)
|
(BRD_X, BRD_Y, +1, +1),
|
||||||
|
(BRD_X + BRD_L, BRD_Y, -1, +1),
|
||||||
# Inner cavity
|
(BRD_X, BRD_Y + BRD_W, +1, -1),
|
||||||
base = base.cut(
|
|
||||||
box(L - WALL * 2, W - WALL * 2, H - WALL,
|
|
||||||
WALL, WALL, WALL)
|
|
||||||
)
|
|
||||||
|
|
||||||
rail_z = H - RAIL_H
|
|
||||||
groove_h = RAIL_H - LIP_H
|
|
||||||
|
|
||||||
# Rail grooves
|
|
||||||
base = base.cut(
|
|
||||||
box(L - WALL * 2, RAIL_D, groove_h,
|
|
||||||
WALL, WALL - RAIL_D, rail_z)
|
|
||||||
)
|
|
||||||
|
|
||||||
base = base.cut(
|
|
||||||
box(L - WALL * 2, RAIL_D, groove_h,
|
|
||||||
WALL, W - WALL, rail_z)
|
|
||||||
)
|
|
||||||
|
|
||||||
# Lid lips
|
|
||||||
lip_z = H - LIP_H
|
|
||||||
|
|
||||||
base = base.fuse(
|
|
||||||
box(L - WALL * 2, LIP_OVER, LIP_H,
|
|
||||||
WALL, WALL, lip_z)
|
|
||||||
)
|
|
||||||
|
|
||||||
base = base.fuse(
|
|
||||||
box(L - WALL * 2, LIP_OVER, LIP_H,
|
|
||||||
WALL, W - WALL - LIP_OVER, lip_z)
|
|
||||||
)
|
|
||||||
|
|
||||||
# Back slot
|
|
||||||
slot_y0 = WALL - RAIL_D
|
|
||||||
slot_yw = W - WALL * 2 + RAIL_D * 2
|
|
||||||
|
|
||||||
base = base.cut(
|
|
||||||
box(WALL + 1.0, slot_yw, RAIL_H,
|
|
||||||
L - WALL, slot_y0, rail_z)
|
|
||||||
)
|
|
||||||
|
|
||||||
# Entry bump
|
|
||||||
BUMP_H = 0.5
|
|
||||||
pad_raw = box(WALL, slot_yw, BUMP_H,
|
|
||||||
L - WALL, slot_y0, rail_z)
|
|
||||||
|
|
||||||
pad_trimmed = pad_raw.common(rbox(L, W, H))
|
|
||||||
base = base.fuse(pad_trimmed)
|
|
||||||
|
|
||||||
# Board clips
|
|
||||||
clip_corners = [
|
|
||||||
(BRD_X, BRD_Y, +1, +1),
|
|
||||||
(BRD_X + BRD_L, BRD_Y, -1, +1),
|
|
||||||
(BRD_X, BRD_Y + BRD_W, +1, -1),
|
|
||||||
(BRD_X + BRD_L, BRD_Y + BRD_W, -1, -1),
|
(BRD_X + BRD_L, BRD_Y + BRD_W, -1, -1),
|
||||||
]
|
]:
|
||||||
|
bot_shell = bot_shell.fuse(make_clip(cx, cy, ix, iy))
|
||||||
|
|
||||||
for cx, cy, ix, iy in clip_corners:
|
# 6. USB-C slot — starts at X = -WALL*3 so it punches through the rounded
|
||||||
base = base.fuse(make_clip(cx, cy, ix, iy))
|
# front face cleanly regardless of fillet radius
|
||||||
|
bot_shell = bot_shell.cut(
|
||||||
|
rounded_slot(WALL * 6, USBC_W, USBC_H,
|
||||||
|
-WALL * 3,
|
||||||
|
W / 2.0 - USBC_W / 2.0,
|
||||||
|
USBC_Z))
|
||||||
|
|
||||||
# USB-C opening
|
# 7. Battery bay
|
||||||
base = base.cut(
|
bot_shell = bot_shell.cut(box(BAT_L, BAT_W, 3.0, BAT_X, BAT_Y, WALL))
|
||||||
rounded_slot(
|
cy0 = BAT_Y + BAT_W / 2.0 - BAT_CLIP_Y / 2.0
|
||||||
WALL * 3,
|
bot_shell = bot_shell.fuse(box(2.0, BAT_CLIP_Y, BAT_H * 0.55, BAT_X - 2.0, cy0, WALL))
|
||||||
USBC_W,
|
bot_shell = bot_shell.fuse(box(2.0, BAT_CLIP_Y, BAT_H * 0.55, BAT_X + BAT_L, cy0, WALL))
|
||||||
USBC_H,
|
|
||||||
-WALL,
|
|
||||||
W / 2 - USBC_W / 2,
|
|
||||||
USBC_Z
|
|
||||||
)
|
|
||||||
)
|
|
||||||
|
|
||||||
# Battery recess
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
base = base.cut(
|
# TOP SHELL (Z = SPLIT_Z → H, open on bottom, closed ceiling at H)
|
||||||
box(BAT_L, BAT_W, 3.0,
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
BAT_X, BAT_Y, WALL)
|
top_h = H - SPLIT_Z # = 7.5 mm
|
||||||
)
|
|
||||||
|
|
||||||
clip_y_start = BAT_Y + BAT_W / 2 - BAT_CLIP_Y / 2
|
# 1. Outer solid spans SPLIT_Z → H
|
||||||
|
top_outer = box(L, W, top_h, 0, 0, SPLIT_Z)
|
||||||
|
top_outer = fillet_vert(top_outer, CR, min_len=top_h * 0.4)
|
||||||
|
|
||||||
base = base.fuse(
|
# Fillet the long horizontal edges of the top shell —
|
||||||
box(2.0, BAT_CLIP_Y, BAT_H * 0.55,
|
# the top edges (Z≈H) are the ones selected in blue in the user's screenshot.
|
||||||
BAT_X - 2.0, clip_y_start, WALL)
|
try:
|
||||||
)
|
th_edges = []
|
||||||
|
for e in top_outer.Edges:
|
||||||
|
if len(e.Vertexes) != 2:
|
||||||
|
continue
|
||||||
|
v0, v1 = e.Vertexes[0], e.Vertexes[1]
|
||||||
|
dx = abs(v0.X - v1.X)
|
||||||
|
dz = abs(v0.Z - v1.Z)
|
||||||
|
dy = abs(v0.Y - v1.Y)
|
||||||
|
# Long edge in X, horizontal, on a long side face —
|
||||||
|
# ONLY at Z≈H (top face). Exclude Z≈SPLIT_Z (the join edge).
|
||||||
|
z_mid = (v0.Z + v1.Z) / 2.0
|
||||||
|
if dx > L * 0.5 and dz < 0.5 and dy < 0.5 and z_mid > H - 1.0:
|
||||||
|
th_edges.append(e)
|
||||||
|
if th_edges:
|
||||||
|
top_outer = top_outer.makeFillet(EDGE_FILLET, th_edges)
|
||||||
|
print(f"Top shell: filleted {len(th_edges)} horizontal edge(s) R={EDGE_FILLET}")
|
||||||
|
else:
|
||||||
|
print("Top shell: no horizontal edges found — skipped")
|
||||||
|
except Exception as exc:
|
||||||
|
print(f"Top shell horizontal fillet skipped: {exc}")
|
||||||
|
|
||||||
base = base.fuse(
|
# 2. Inner cavity: side walls WALL thick, CEILING at H-WALL (WALL-thick roof),
|
||||||
box(2.0, BAT_CLIP_Y, BAT_H * 0.55,
|
# FLOOR open (starts at SPLIT_Z — nothing blocks the bottom opening).
|
||||||
BAT_X + BAT_L, clip_y_start, WALL)
|
# Cavity box: X from WALL→L-WALL, Y from WALL→W-WALL, Z from SPLIT_Z→H-WALL
|
||||||
)
|
top_cav_lx = L - WALL * 2
|
||||||
|
top_cav_ly = W - WALL * 2
|
||||||
|
top_cav_lz = top_h - WALL # = 7.5 - 3.5 = 4.0 mm interior height
|
||||||
|
top_inner = box(top_cav_lx, top_cav_ly, top_cav_lz,
|
||||||
|
WALL, WALL, SPLIT_Z) # starts exactly at SPLIT_Z
|
||||||
|
top_shell = top_outer.cut(top_inner)
|
||||||
|
|
||||||
# Circular notch in back wall - centred on base
|
# 3. Groove at the bottom of the top shell, starting at SPLIT_Z
|
||||||
notch_cz = rail_z + LID_H
|
# The groove is a frame-shaped recess cut into the inner face of the walls.
|
||||||
base = base.cut(circular_notch(L, W / 2, notch_cz, NOTCH_R, NOTCH_DEPTH))
|
# It goes from Z=SPLIT_Z up to Z=SPLIT_Z+GROOVE_H.
|
||||||
|
# Width = GROOVE_T (slightly wider than tongue).
|
||||||
|
g_slab = box(top_cav_lx, top_cav_ly, GROOVE_H,
|
||||||
|
WALL, WALL, SPLIT_Z)
|
||||||
|
g_cut = box(top_cav_lx - GROOVE_T*2, top_cav_ly - GROOVE_T*2, GROOVE_H + 1,
|
||||||
|
WALL + GROOVE_T, WALL + GROOVE_T, SPLIT_Z - 0.5)
|
||||||
|
groove = g_slab.cut(g_cut)
|
||||||
|
top_shell = top_shell.cut(groove)
|
||||||
|
|
||||||
# Lid
|
# 4. Button aperture — brute-force: run cylinder from Z=SPLIT_Z to Z=H+2.
|
||||||
TAB_W = RAIL_D - TOL + 0.5
|
# It will punch through the ceiling regardless of any topology.
|
||||||
LID_L = L - WALL * 2 - TOL
|
top_shell = top_shell.cut(
|
||||||
LID_EXTRA_TOL = 0.5
|
cyl(BTN_HOLE_R, H - SPLIT_Z + 2, BTN_X, BTN_CY, SPLIT_Z))
|
||||||
|
|
||||||
LID_W = (
|
# 5. Button PCB shelf frame
|
||||||
W - WALL * 2
|
shelf_ox = BTN_X - BPCB_L / 2.0
|
||||||
- (TOL + LID_EXTRA_TOL) * 2
|
shelf_oy = BTN_CY - BPCB_W / 2.0
|
||||||
+ TAB_W * 2
|
shelf_h = 1.5
|
||||||
)
|
shelf_slab = box(BPCB_L + SHELF_WALL*2, BPCB_W + SHELF_WALL*2, shelf_h,
|
||||||
|
shelf_ox - SHELF_WALL, shelf_oy - SHELF_WALL,
|
||||||
|
PCB_BOT_Z - shelf_h)
|
||||||
|
shelf_hole = box(BPCB_L, BPCB_W, shelf_h + 2.0,
|
||||||
|
shelf_ox, shelf_oy, PCB_BOT_Z - shelf_h - 1.0)
|
||||||
|
shelf = shelf_slab.cut(shelf_hole)
|
||||||
|
if floor_top_shell < PCB_BOT_Z < H - WALL:
|
||||||
|
top_shell = top_shell.fuse(shelf)
|
||||||
|
|
||||||
lid_y0 = WALL + TOL + LID_EXTRA_TOL - TAB_W
|
# 6. Screw posts on top-shell floor
|
||||||
lid = box(LID_L, LID_W, LID_H, 0, lid_y0, 0)
|
if POST_H > 0.5:
|
||||||
|
for py in [BTN_CY - POST_SEP/2.0, BTN_CY + POST_SEP/2.0]:
|
||||||
|
p = cyl(POST_R, POST_H, BTN_X, py, floor_top_shell)
|
||||||
|
ph = cyl(POST_IR, POST_H + 1.0, BTN_X, py, floor_top_shell)
|
||||||
|
top_shell = top_shell.fuse(p)
|
||||||
|
top_shell = top_shell.cut(ph)
|
||||||
|
|
||||||
lid.translate(Base.Vector(WALL + TOL, 0, rail_z))
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
|
# BUTTON CAP (separate printed part)
|
||||||
|
#
|
||||||
|
# Geometry at origin:
|
||||||
|
# Shaft: Z = 0 (bottom/inner) → Z = CAP_SHAFT_H = WALL (top/flush)
|
||||||
|
# Rim: Z = -CAP_RIM_H → Z = 0 (hangs inside cavity)
|
||||||
|
# Nubbin: Z = -CAP_RIM_H-NUBBIN_H → Z = -CAP_RIM_H
|
||||||
|
#
|
||||||
|
# Placed so shaft top = H → flush with top face.
|
||||||
|
# Rim is entirely inside the cavity. No part protrudes above H.
|
||||||
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
|
cap_shaft = cyl(CAP_SHAFT_R, CAP_SHAFT_H)
|
||||||
|
cap_rim = cyl(CAP_RIM_R, CAP_RIM_H, 0, 0, -CAP_RIM_H)
|
||||||
|
cap_nub = cyl(NUBBIN_R, NUBBIN_H, 0, 0, -CAP_RIM_H - NUBBIN_H)
|
||||||
|
cap_raw = cap_shaft.fuse(cap_rim).fuse(cap_nub)
|
||||||
|
# No fillet on cap top rim — cap sits flush inside aperture so a fillet
|
||||||
|
# would create a visible chamfer ring against the hole edge.
|
||||||
|
cap_placed = cap_raw.copy()
|
||||||
|
cap_placed.translate(Base.Vector(BTN_X, BTN_CY, H - CAP_SHAFT_H))
|
||||||
|
|
||||||
# Final objects
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
base_obj = doc.addObject("Part::Feature", "Pointer_Base")
|
# REGISTER OBJECTS
|
||||||
base_obj.Shape = base
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
base_obj.ViewObject.ShapeColor = (0.12, 0.12, 0.14)
|
bot_obj = doc.addObject("Part::Feature", "Shell_Bottom")
|
||||||
|
bot_obj.Shape = bot_shell
|
||||||
|
bot_obj.ViewObject.ShapeColor = (0.12, 0.12, 0.14)
|
||||||
|
bot_obj.ViewObject.Transparency = 0
|
||||||
|
|
||||||
lid_obj = doc.addObject("Part::Feature", "Pointer_Lid")
|
top_obj = doc.addObject("Part::Feature", "Shell_Top")
|
||||||
lid_obj.Shape = lid
|
top_obj.Shape = top_shell
|
||||||
lid_obj.ViewObject.ShapeColor = (0.28, 0.28, 0.34)
|
top_obj.ViewObject.ShapeColor = (0.20, 0.20, 0.26)
|
||||||
lid_obj.ViewObject.Transparency = 25
|
top_obj.ViewObject.Transparency = 0
|
||||||
|
|
||||||
|
cap_obj = doc.addObject("Part::Feature", "Button_Cap")
|
||||||
|
cap_obj.Shape = cap_placed
|
||||||
|
cap_obj.ViewObject.ShapeColor = (0.80, 0.80, 0.86)
|
||||||
|
cap_obj.ViewObject.Transparency = 0
|
||||||
|
|
||||||
doc.recompute()
|
doc.recompute()
|
||||||
Gui.activeDocument().activeView().viewIsometric()
|
Gui.activeDocument().activeView().viewIsometric()
|
||||||
Gui.SendMsgToActiveView("ViewFit")
|
Gui.SendMsgToActiveView("ViewFit")
|
||||||
|
|
||||||
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
|
# SUMMARY
|
||||||
|
# ═════════════════════════════════════════════════════════════════════════════
|
||||||
|
print("=" * 62)
|
||||||
|
print("IMU Pointer v7")
|
||||||
|
print("=" * 62)
|
||||||
|
print(f"Body: {L:.0f} × {W:.0f} mm")
|
||||||
|
print(f"Height: {H:.0f} mm uniform (no taper)")
|
||||||
|
print(f"Wall: {WALL:.1f} mm CR = {CR:.1f} mm Edge fillet = {EDGE_FILLET:.1f} mm")
|
||||||
|
print(f"Split Z: {SPLIT_Z:.1f} mm "
|
||||||
|
f"(USB-C top = {USBC_Z + USBC_H:.1f} mm)")
|
||||||
|
print(f"Top shell interior height: {top_cav_lz:.1f} mm (Z {SPLIT_Z:.1f} → {H - WALL:.1f})")
|
||||||
|
print()
|
||||||
|
print(f"Tongue H/T: {TONGUE_H:.1f} / {TONGUE_T:.1f} mm")
|
||||||
|
print(f"Groove H/T: {GROOVE_H:.2f} / {GROOVE_T:.2f} mm")
|
||||||
|
print()
|
||||||
|
print(f"Button hole: ⌀{BTN_HOLE_R*2:.0f} mm X={BTN_X} Y={BTN_CY:.0f}")
|
||||||
|
print(f"Cap shaft: ⌀{CAP_SHAFT_R*2:.1f} mm × {CAP_SHAFT_H:.1f} mm (flush, Z {H-WALL:.1f}→{H:.1f})")
|
||||||
|
print(f"Cap rim: ⌀{CAP_RIM_R*2:.0f} mm × {CAP_RIM_H:.1f} mm (retention, below top face)")
|
||||||
|
print()
|
||||||
|
print(f"PCB top Z: {PCB_TOP_Z:.2f} mm (above split floor {floor_top_shell:.1f} mm)")
|
||||||
|
print(f"PCB bot Z: {PCB_BOT_Z:.2f} mm")
|
||||||
|
print(f"Post H: {POST_H:.2f} mm ⌀{POST_OD:.0f}/{POST_ID:.1f} mm sep={POST_SEP:.0f} mm c-to-c")
|
||||||
|
print()
|
||||||
|
print(f"Switch stack: body={SWITCH_BODY_H} + stem={STEM_H} + gap={GAP} mm")
|
||||||
|
print(" Adjust SWITCH_BODY_H / STEM_H if your Omron differs.")
|
||||||
|
print("=" * 62)
|
||||||
Reference in New Issue
Block a user